View R2A-700D1V2_8382675.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

issued date : 11/09/2012 specification a?? a?? a?? a?? a?Q a?Q a?Q a?Q / model name R2A-700D1V2 a? a? a? a? / description 700w+700w redundant power supply. / revision 1.3 ??o ??o ??o ??o / revision history rev. date revision description ? ? ? ? modify by ?J ?J ?J ?J cust. approval J J J J app. date 1.0 aug.08 2011 dc-dc { modified the circuit for dc-dc backplane kevin chen aug.10, 2011 1.1 jan. 09 2012 modified the 6.3 value. jacky jan jan. 09, 2012 1.2 aug.28, 2012 modified item 12 environmental jacky jan sep. 06, 2012 1.3 nov.09, 2012 modified the 14.2 dc output cables and stick mindy chung nov. 12, 2012 ? / prepared by z / checked by ? / approved by kevin jacky sure star sure star
? contents 1. general description 2. ?? ?? ?? ?? input characteristics 2.1. ??l? ac input voltage and frequency 2.2. ?c? input current and inrush current 2.3. power factor 3. power efficiency 4. ?? ?? ?? ?? output characteristics 4.1. ??{ output voltage & current regulation 4.2. ?y dc output ripple & noise 4.3. ??rg hold up time 4.4. rg rise time 4.5. ?B? rg dynamic load response time 4.6. h_P remote on/off control 5. ?? ?? ?? ?? power good signal 6. o o o o protection 6.1. ^o over voltage protection 6.2. ?o under-voltage protection 6.3. ^o over current protection 6.4. o short circuit protection 6.5. ^?o thermal protection 7. ??B ??B ??B ??B power system signal status 7.1. QB buzzer status 7.2. ??? led indicators 7.3. ttl ? ttl signal 8. ?d ?d ?d ?d load sharing sure star sure star
9. ^ ^ ^ ^ isolation 9.1. ^ insulation resistance 9.2. ?^ dielectric withstand voltage 9.3. ? leakage current 10. ? ? ? ? ? ? ? ? safety requirements 11. ? ? ? ? emc 11.1. ? ?_ emi 11.2. ? ems 12. hl hl hl hl environmental 12.1. ? temperature 12.2. h humidity 12.3. ? altitude 12.4. s? cooling method 13. ? ? ? ? reliability 13.1 ??rg mtbf qualification 14. C? C? C? C? ?B ?B ?B ?B mechanical 2d drawing and power connector 14.1. ^?D outside dimension 14.2. ?? dc output cables sure star sure star
1. general description this specification describes the performance charac teristics of a 700 watts hot swappable, 1+1 power system with +3.3v,+5v,+12v, -12v main dc outp uts, and 5v standby outputs. the system is configured to hold two identical 700w pow er supply modules, sure star model R2A-700D1V2. 2. ?? ?? ?? ?? input characteristics 2.1. ?? l ac input voltage and frequency ? minimum ? nominal ? maximum unit 90 100~240 264 vac 47 50~60 63 ? hz 2.2. ?c input current and inrush current ?? ac input voltage ? max. input current per power supply module ? inrush current per power supply module 115vac 12a 30a 230vac 6a 60a 2.3. power factor 90vac 115vac 230vac 264vac 0.99 0.98 0.95 0.92 3. power efficiency ?MdB 115 60 ?? ?? 80%(min) the minimum efficiency of the power supply is 80% a t full load and 115vac/60hz input. sure star sure star
4. ?? ?? ?? ?? output characteristics 4.1. ??{ output voltage & current regulation ?? output voltage min. current ~ rated current { regulation +3.3v 1a 25a 5 +5v 1a 25a 5 +12v 1a 57a 5 -12v 0a 1a 5 +5vsb 0.5a 3.5a 5 note: 5v 3.3v ??^ 190 . the combined total power from 5v & 3.3v shall not e xceed 190w. 4.2. ?y dc output ripple & noise output voltage ripple & noise (max.) +3.3v 60mvp-p +5v 60mvp-p +12v 120mvp-p -12v 120mvp-p +5vsb 50mvp-p note: 1. y lO 20 ?? ripple & noise bandwidth is set to 20mhz 2. ??K?? 0.1 uf ??? 10 uf ? y? y use a 0.1uf ceramic capacitor in parallel with a 10 uf electrolytic capacitor at output connector terminals for ripple & noise me asurements 4.3. ??rg hold up time output voltage 115vac input 230vac input +3.3v 16ms 16ms +5v 16ms 16ms +12v 16ms 16ms -12v 16ms 16ms +5vsb 16ms 16ms note: ??MdB all of dc output at full load. sure star sure star
4.4. rg rise time output voltage 115/230vac input & full load +3.3v 20ms (max.) +5v 20ms (max.) +12v 20ms (max.) -12v 20ms (max.) +5vsb 20ms (max.) note: rg?? 10% 90% ?rg the rise time measured is when the output voltages rise from10% to 90% of specified output voltage vout observed on the chann el waveform. 4.5. ?B? rg dynamic load response time the following shall apply to the 3.3 v, 5 v, and 12 v outputs: output voltage for each output shall recover to wit hin 5 % of its steady state level in less than 1 ms under the following conditions: ac input voltage: 90vac ~ 264vac repetition rate of 100hz with 50 % duty cycle output step load size load slew rate capacitive loa d +3.3v 30% to 100% to 30% load 0.5 a/ u sec 6000uf +5v 30% to 100% to 30% load 0.5 a/ u sec 6000uf +12v 60% to 100% to 60% load 1 a/ u sec 6000uf +5sb 0% to 100% to 0% load 0.5 a/ u sec 350uf 4.6. h_P remote on/off control the main outputs of this power supply (3.3v,5v,12v ,-12v) shall be energized when input signal*pson is active. *pson is an active low ttl c ompatible signal referenced to the +5v standby common. this input signal shall be an open collector signal capable of sinking a minimum of 1.6ma. when *pson becomes inactive, the main outputs shall be disabled. psu on psu off pson signal low (0.8v max) hi (2v max) sure star sure star
5. ?? ?? ?? ?? power good signal the system shall have an active high ttl compatible signal capable of sinking 1ma and sourcing 100ua. the signal shall become active with in 100 to 500 ms from the instant +5v output reaches a steady state level within the specified r egulation limits. it shall become inactive at le ast 1 ms before +5v drops to below the lower regulation limit. power good @ 115/230vac , full load 200ms ~ 500ms power fail @ 115/230vac , full load 1ms (min.) 6. o o o o protection 6.1. ^o over voltage protection output min max comments +3.3v 3.75v 4.3v psu shutdown +5v 5.7v 6.9v psu shutdown +12v 13v 14.3v psu shutdown note ??? 230 pd d?y? the power supply shall be test at max ac voltage (2 30vac) and min load or no load. 6 .2. ?o under-voltage protection output min max comments +3.3v 2.0v 2.4v psu shutdown +5v 3.3v 3.7v psu shutdown +12v 8.5v 9.5v psu shutdown note ??? 230 pd d?y? the power supply shall be test at max ac voltage (2 30vac) and min load or no load. 6 .3. ^o over current protection output over current(type) over current(max.) comments +3.3v R 27.5a 37.5a psu shutdown +5v R 27.5a 37.5a psu shutdown +12v R 62.7a 85.5a psu shutdown note ^oy?~?dry? the over current protection should be tested at oth er load rating. sure star sure star
6.4. o short circuit protection output comments +3.3v psu shutdown +5v psu shutdown +12v psu shutdown note oy? ~?dry? the short circuit protection should be tested at ot her load rating. 6.5. ^?o thermal protection ?? ^ 86 5 ?M^?oB ??? ??? ??? the power supply shall go into thermal protection a s the case temperature exceeds 86 5 limit. the output shall recover only when the tempe rature becomes normal and ac power is turned on again. 7. ??B ??B ??B ??B power system signal status 7.1. QB buzzer status power supply condition buzzer status no ac power to all psu off ac present/only standby output on off power supply dc outputs on and ok off power supply failure beeping 7.2. ??? led indicators power supply condition power system status per power module status led color red green orange no ac power to all psu off off off ac present/only standby output on on off off power supply dc outputs on and ok off on on power supply failure off blinking off sure star sure star
7.3. ttl ? ttl signal output condition power supply condition min. max. normal(power supply on) 3v 5.25v failure(power supply off) 0v 1v 8. ?d ?d ?d ?d load sharing ?? output voltage ?d load current ?d ? load share voltage +12v 1a +0.48v ~ +0.52v +5v 1a +0.33v ~ +0.37v +3.3v 1a +0.33v ~ +0.37v 9. ^ ^ ^ ^ isolation 9.1. ^ insulation resistance input to output 500vdc , 50m ohms min.( at room temperature) input to fg 500vdc , 50m ohms min.( at room temperature) output to fg non insulation 9.2. ?^ dielectric withstand voltage input to output 1834vac (30 ma) for 1 minute. input to fg 1834vac (30 ma) for 1 minute. output to fg non insulation 9.3. ? leakage current 120-264 /50-60 ?r ? 3.5ma 3.5ma max. at 120~264vac/50~60hz. 10. ? ? ? ? ? ? ? ? safety requirements -iec 60950-1 -tuv en 60950-1 -ul or cul -bsmi -ccc sure star sure star
11. ? ? ? ? emc ??? _M?? the power supply shall comply with the following cr iterion: 11.1. ?? _ emi 1) conduction emission: ?_ a.en55022:2006/a1:2007 class a; en55024:1998/a1:200 1/a2:20003. b.cispr pub.22 and fcc part 15 subpart b class a. 2) radiated emission : ( ?_ ) a.en55022:2006/a1:2007 class a; en55024:1998/a1:200 1/a2:20003. b.cispr pub.22 and fcc part 15 subpart b class a. 12. hl hl hl hl environmental 12.1. temperature operating : 0 to +40 non operating: -20 to +70 12.2. humidity operating : 5% to 95%, non-condensing non operating: 20% to 90%,non-condensing 12.3. altitude: altitude during operation: up to 2000 m altitude of test laboratory: below 2000 m 12.4. s? cooling method by ball bearing dc fan. 13. ? ? ? ? reliability 13.1 ??rg mtbf qualification using mil - hdbk -217f the calculated mtbf 100,000 hours at 25 sure star sure star
? 14. C? C? C? C? ?B ?B ?B ?B mechanical 2d drawing and power connector 14.1. outside dimension:265(d)x101(w)x84(h)mm 6#-32(x3) 6#-32(x4) sing date ? revisions ? rev descripion reset _P model no ? part no ? mm of date sheet ? draw no D? units draw by LD check by approve by ? ? projection: material ? ?? : S : .2 .1 .025 .x= .xx= .xxx= toleances: jacky r2a-600d1v2 ^?D sure star may,5,2010
? p24 14 16 15 17 13 18 19 21 20 22 23 24 1 2 4 3 59 78 6 11 12 10 orange(+3.3v) red(+5v) pin no. wire color pin no. gray(pg) purple(+5vsb) nc blue(-12v) yellow (+12v) green(ps-on) wire color black(gnd) 470mm/18awg 470mm/22awg 470mm/18awg 470mm/20awg 470mm/20awg 470mm/18awg length length housing 470mm/18awg 470mm/18awg orange(+3.3v) orange(+3.3v) orange(+3.3vs) black(gnd) black(gnd) red(+5v) yellow (+12v) orange(+3.3v) black(gnd) black(gnd) black(gnd) black(gnd) black(gnd) red(+5v) red(+5v) red(+5v) 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg connector housing: molex 39-01-2240 or equivalent 24pins(eps12v) terminal: m olex 39-00-0039 or equivalent ss-r2a(12 ) mod el no ? part no ? mm of date sheet ? draw no D? un its draw by. LD c heck by. approve by. ? ? projection: mater ial ? ?? : S : .x= .xx= .xxx= toleances: kevin sure star 2011,11,02 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 470mm/18awg 01 com com black 470mm 15mm length wire type signal wire color pin no. 3 4 2 1 18awg 18awg 18awg 18awg black yellow +12v yellow +12v 4pins(atx12v,for p4) connector housing: molex 39-01-0280 or equivalent terminal: molex 39-00-0060 or equivalent housing p4 18awg 18awg 18awg 18awg 18awg 1 2 4 3 5 +5v pin no. wire color signal wire type length black yellow +3v3 com com +12v housing pn 18awg 18awg 18awg 18awg 18awg 1 24 3 5 +5v pin no. wire color signal wire type length black yellow +3v3 com com +12v housing black orange red black orange red 150mm 15mm 480mm 15mm connector housing: molex 39-01-0280 or equivalent 6pins 18awg 18awg 18awg 18awg 18awg 18awg 1 2 4 3 5 +12v com 6 pin no. wire color signal wire type length yellow 470mm 20mm yellow yellow +12v +12v com com terminal: molex 39-00-0060 or equivalent housing p6 black black black pp housing: molex 675820000 or equivalent terminal: molex 675810000 or equivalent s.ata hdd pj pk l=480mm+/-20 mm l=150mm+/- 10mm l=150mm +/-10mm l=150mm +/-10mm 22awg 1007 l=480mm+/-20 mm l=150mm+/- 10mm l=150mm+/- 10mm pd pe pf pl pm 4 3 2 1 l=480mm+/-20 mm l=150mm+/- 10mm l=150mm+/- 10mm pa pb pc pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 5 led pin2 pin1 187p pin2 pin1 h2510 5 led power module/system status led alarm reset switch connector 251 0 ttl signal cable 5 led external led red / orange brown / white pw1 led orange pw2 led orange green / white red / white black (com) r ed (+5v) gray (com) gray (reset) l=480mm+/-20 mm l=150mm+/- 10mm pn po 4 3 2 15 (1-3) (4-6) (7-9) (10-12) (13-15) 4 3 2 15 (1-3) (4-6) (7-9) (10-12) (13-15) l=480mm+/-20 mm l=150mm+/- 10mm pp pq 4 3 2 15 (1-3) (4-6) (7-9) (10-12) (13-15) 4 3 2 15 (1-3) (4-6) (7-9) (10-12) (13-15) pin4 l=470mm+/-20 mm pin1 p6 pin8 pin4 pin1 pin5 pin4 pin2 pin1 pin3 p8 p4 l=470mm20mm l=470mm20mm l=470mm20mm pin13 pin1 pin12 pin24 p24 connector housing: molex 39-01-0280 or equivalent 8pins(eps12v) 18awg 18awg 18awg 18awg 18awg 18awg 18awg 18awg 1 2 4 3 5 com +12v 78 6 pin no. wire color signal wire type length black black 470mm 15mm black black yellow yellow yellow yellow com com com +12v +12v +12v terminal: molex 39-00-0060 or equivalent housing p8 terminal:amp 60619-4 or equivalent 4pins(hd/cd-rom/rw):p4h1~p4h4 com length wire size signal wire color pin no. 3 4 2 1 18awg 18awg 18awg 18awg black red +12v yellow black com +5v connector housing: am p 480424-0 or equivalent pa housing com 3 4 2 1 18awg 18awg 18awg 18awg black red +12v yellow black com +5v com 150mm 15mm 3 4 2 1 black red +12v yellow black com +5v 150mm 15mm 480mm 15mm terminal: amp 170262-2 or equivalent 4pins(floppy disk):p4f connector housing: amp 171822-4 or equivalent 18awg 18awg 18awg 18awg com 150mm 15mm 3 4 2 1 black red +12v yellow black com +5v pm 22awg 22awg 22awg 22awg pd pg pj po pq white white green external led red brown white wire color name pw1led pw2led com 860mm 20mm length wire type signal wire color pin no. 2 1 22awg 22awg black +5v red 860mm 20mm length wire type 22awg 22awg 22awg 22awg 22awg 1 2 pin no. wire color signal wire type length 860mm 20mm gray gray led color orange red/orange com rest connector housing: m olex 22-01-3027 or equivalent ttl signal alarm reset switch connector power m odule/system status led orange l=480mm+/-20 mm l=150mm+/- 10mm l=150mm+/- 10mm pg ph pi pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pin4 pin3 pin2 pin1 pb pe ph pk pc pf pi pl 14.2. dc output cables

▲Up To Search▲

Price & Availability of R2A-700D1V2

	To Download R2A-700D1V2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .